Difference between revisions of "System portal setup"

From OpenMotics
Jump to navigation Jump to search
 
(4 intermediate revisions by the same user not shown)
Line 70: Line 70:
  
 
[[File:Portal_settings_outputs_edit_1.png|500px|Output wizard]]
 
[[File:Portal_settings_outputs_edit_1.png|500px|Output wizard]]
 +
 +
=== Settings > Inputs ===
 +
 +
This page displays an overview of all Inputs in the system.
 +
 +
[[File:Portal_settings_inputs.png|500px|Inputs]]
 +
 +
When selecting an Input the bottom section displays all settings. The edit button starts the Input configuration wizard.
 +
 +
The first step allows to set the name and select the Input's global functionality. Selecting an option immediately displays some more information about that functionality. Selecting the right option will make it easier to enter the configuration. Using the advanced configuration allows access to all features.
 +
 +
[[File:Portal_settings_inputs_1.png|500px|Input wizard 1]]
 +
 +
The second step depends on the selected functionality.
 +
 +
[[File:Portal_settings_inputs_2_pulsecounter.png|500px|Pulsecounter]]
 +
 +
[[File:Portal_settings_inputs_2_outputs.png|500px|Outputs]]
 +
 +
[[File:Portal_settings_inputs_2_motionsensor.png|500px|Motion sensor]]
 +
 +
[[File:Portal_settings_inputs_2_groupaction.png|500px|Group action]]
 +
 +
[[File:Portal_settings_inputs_2_advanced.png|500px|Advanced configuration]]
 +
 +
The third step is only available if the Input is one via the CAN system (microCAN module connected to a CAN Control module). It allows to configure the feedback led for that input. It can either be disabled, linked to the state of an output, or display more generic feedback (e.g. whether some light in the house is on/off). If more complex feedback is needed, these leds can also be configured in Group Actions or "Advanced configuration".
 +
 +
[[File:Portal_settings_inputs_3_nofeedback.png|500px|No feedback]]
 +
 +
[[File:Portal_settings_inputs_3_output.png|500px|Output feedback]]
 +
 +
[[File:Portal_settings_inputs_3_generic.png|500px|Generic feedback]]
 +
 +
=== Settings > Sensors ===
 +
 +
An overview of all installed sensors with their values. An indicator will show sensor values that are increasing or decreasing.
 +
 +
[[File:Portal_settings_sensors.png|500px|Sensors]]
 +
 +
Again, an edit wizard allows to make basic changes.
 +
 +
[[File:Portal_settings_sensors_edit_1.png|500px|Edit sensor]]
 +
 +
=== Settings > Thermostats ===
 +
 +
The thermostats settings page shows both the global thermostat settings (e.g. pump delay, which outputs control cooling/heating switch, ...) as the settings of the individual thermostats
 +
 +
[[File:Portal_settings_thermostats.png|500px|Thermostats]]
 +
 +
The global thermostat settings wizard allows to change the global thermostat settings
 +
 +
[[File:Portal_settings_thermostats_1_general.png|500px|Global settings 1]]
 +
 +
[[File:Portal_settings_thermostats_2 switches.png|500px|Global settings 2]]
 +
 +
When selecting an individual thermostat, the page shows the thermostat's settings (timings and temperatures). Changing those temperature/timing values is not yet supported, but the other parameters can be changed.
 +
 +
[[File:Portal_settings_thermostats_selected.png|500px|Individual thermostat]]
 +
 +
[[File:Portal_settings_thermostats_single_1.png|500px|Individual thermostat settings]]

Latest revision as of 16:06, 25 February 2018

Main documentation for the Cloud Portal

The Cloud Portal is currently in beta and will replace the current existing Cloud. This means currently not all functionality is available in the Portal.

General

Navigate to https://portal.openmotics.com

Main pages

Logging in

The main login page allows the user to enter username & password.

Login page

If a private computer is used, it's possible to remember the credentials for a given amount of time. If using a recent version of Chrome the option "permanent" might be showed, which interfaces with Chrome itself to let it store the credentials. In that case, the portal will automatically login in the future.

Login page

If two factor authentication was selected, the TOTP will be requested. Permanent mode is currently not possible when two factor authentication is set.

TOTP

Dashboard

Once logged in, the dashboard is the default page that will be showed. It shows the amount of lights that are on, and shows the amount of apps that are installed.

Dashboard

Lights & Outputs

This page is used to control all lights and outputs.

Lights & outputs

Thermostats

The thermostat page contains basic controls to set the desired temperatures.

Thermostats

Energy

The energy page shows the current energy consumption of connected Energy Modules.

Energy

Settings

Settings > Initialisation

The initialisation page shows the modules that are installed in the system.

Initialisation

To add new modules to the system open the initialisation wizard by clicking the start discovery button. Make sure to read all instructions carefully.

Discover wizard

After the wizard closes, press the buttons on all new modules. The page will show the newly discovered modules. Don't forget to exit discovery mode once finished.

Stop discover

Settings > Outputs

This page displays an overview of all Outputs in the system with their state. When selecting an output, various settings can be changed using the edit button at the bottom of the page. This open a wizard.

Outputs

Output wizard

Settings > Inputs

This page displays an overview of all Inputs in the system.

Inputs

When selecting an Input the bottom section displays all settings. The edit button starts the Input configuration wizard.

The first step allows to set the name and select the Input's global functionality. Selecting an option immediately displays some more information about that functionality. Selecting the right option will make it easier to enter the configuration. Using the advanced configuration allows access to all features.

Input wizard 1

The second step depends on the selected functionality.

Pulsecounter

Outputs

Motion sensor

Group action

Advanced configuration

The third step is only available if the Input is one via the CAN system (microCAN module connected to a CAN Control module). It allows to configure the feedback led for that input. It can either be disabled, linked to the state of an output, or display more generic feedback (e.g. whether some light in the house is on/off). If more complex feedback is needed, these leds can also be configured in Group Actions or "Advanced configuration".

No feedback

Output feedback

Generic feedback

Settings > Sensors

An overview of all installed sensors with their values. An indicator will show sensor values that are increasing or decreasing.

Sensors

Again, an edit wizard allows to make basic changes.

Edit sensor

Settings > Thermostats

The thermostats settings page shows both the global thermostat settings (e.g. pump delay, which outputs control cooling/heating switch, ...) as the settings of the individual thermostats

Thermostats

The global thermostat settings wizard allows to change the global thermostat settings

Global settings 1

Global settings 2

When selecting an individual thermostat, the page shows the thermostat's settings (timings and temperatures). Changing those temperature/timing values is not yet supported, but the other parameters can be changed.

Individual thermostat

Individual thermostat settings