Difference between revisions of "Energy module front panel LED functionality"

From OpenMotics
Jump to navigation Jump to search
Line 4: Line 4:
 
explanation per led:
 
explanation per led:
 
[<frequency> <duty cycle>]
 
[<frequency> <duty cycle>]
The one in bold is the   
+
The one in bold is the default value  
 +
 
  
=main program=
 
 
== powerled ==  
 
== powerled ==  
* '''[no 100%]''' led is on : main program is running
+
* '''[no 100%]''' led is on : main program
 
* [1Hz 90%] led blinks every second but almost constant on : bootloader mode
 
* [1Hz 90%] led blinks every second but almost constant on : bootloader mode
  
 +
=main program=
 
== statusled ==
 
== statusled ==
 
* [1Hz 10%] led blinks short every second : main process is not yet started, if this stays for a long time there is something wrong to initialize.
 
* [1Hz 10%] led blinks short every second : main process is not yet started, if this stays for a long time there is something wrong to initialize.
Line 24: Line 25:
  
 
=bootloader=
 
=bootloader=
 +
 +
== statusled ==
 +
* [1Hz 10%] led blinks short every second : main process is not yet started, if this stays for a long time there is something wrong to initialize.
 +
* '''[1Hz 50%]''' led blinks normal ones a second : main process is running and everything is ok, there is also communication
 +
* [4Hz 50%] led blinks normal but fast : main process is running and all ok, but there is no communication 
 +
* [1Hz 90%] led is almost constant on but blinks off ones a second : addressmode
 +
 +
== voltage 1-3 ==
 +
The leds represent the address of the module in binary format
 +
[V1 V2 V3]
 +
ex. if V2 and V3 is on -> 011 = address 3
 +
 +
For all addresses above 7, module 8 operation is preformed.

Revision as of 12:37, 19 March 2016

There are 5 leds on the toppanel. The status of those leds depends on there blinking frequency and duty cycle.

explanation per led: [<frequency> <duty cycle>] The one in bold is the default value


powerled

  • [no 100%] led is on : main program
  • [1Hz 90%] led blinks every second but almost constant on : bootloader mode

main program

statusled

  • [1Hz 10%] led blinks short every second : main process is not yet started, if this stays for a long time there is something wrong to initialize.
  • [1Hz 50%] led blinks normal ones a second : main process is running and everything is ok, there is also communication
  • [4Hz 50%] led blinks normal but fast : main process is running and all ok, but there is no communication
  • [1Hz 90%] led is almost constant on but blinks off ones a second : addressmode

voltage 1-3

The status of the 3 voltage leds is the same but each for its own voltage channel

  • [1Hz 10%] led blinks short every second : There is commnication with the the processor who measures the voltage but the voltage level is to low
  • [1Hz 90%] led is almost constant on but blinks off ones a second : There is a voltage signal measured on the corresponding voltage channel and the voltage is higher than 50V
  • [4Hz 50%] led blinks normal but fast : There is a problem to communicate with the processor who measures the voltage.

bootloader

statusled

  • [1Hz 10%] led blinks short every second : main process is not yet started, if this stays for a long time there is something wrong to initialize.
  • [1Hz 50%] led blinks normal ones a second : main process is running and everything is ok, there is also communication
  • [4Hz 50%] led blinks normal but fast : main process is running and all ok, but there is no communication
  • [1Hz 90%] led is almost constant on but blinks off ones a second : addressmode

voltage 1-3

The leds represent the address of the module in binary format [V1 V2 V3] ex. if V2 and V3 is on -> 011 = address 3

For all addresses above 7, module 8 operation is preformed.