AIO API Event Codes

Type	Action	DeviceNr.MSB	DeviceNr.LSB	Data0	Data1	Data2	Data3	Description
0	0	x.MSB	x.LSB	y	z	u.MSB	u.LSB	Output x off: This Event will be send when an output is switched off with dimmer value y, timer type z and timer value u. See Note 1.
0	1	x.MSB	x.LSB	y	z	u.MSB	u.LSB	Output x on: This Event will be send when an output is switched on with dimmer value y, timer type z and timer value u. See Note 1.
0	2	x.MSB	x.LSB	y	-	-	-	Output x lock/unlock status: This Event will be send when output x is locked/unlock. y=0->Unlock, y=1->Lock
1	0	x.MSB	x.LSB	0	0	0	0	Input x Released: This Event will be send when an input is released.
1	1	x.MSB	x.LSB	0	0	0	0	Input x Pressed: This Event will be send when an input is pressed.
1	2	x.MSB	x.LSB	y	-	-	-	Input x lock/unlock status: This Event will be send when Input x is locked/unlock. y=0->Unlock, y=1->Lock
2	0	0	x	0	y	0	0	Temperature sensor x changed: This Event will be send when Temperature sensor x has changed, new temperature will be found in y
2	1	0	x	0	y	0	0	Humidity sensor x changed: This Event will be send when Humidity sensor x has changed, new humidity will be found in y
2	2	0	x	y.MSB	y.LSB	0	0	Brightness sensor x changed: This Event will be send when Brightness sensor x has changed, new humidity will be found in y
2	3	0	x	y.MSB	y.LSB	z.MSB	z.LSB	Air quality sensor x changed: This Event will be send when values sensor x have changed, new CO2 will be found in y and VOC in z.
20	0	0	x	Mode	Setpoint	0	0	Thermostat x has changed: The Thermostat setpoint/mode has been modified by the slave device (For example the Modbus thermostat connected to the Micro CAN has an updated value set by the user)
20	0	0	x	Mode	Setpoint	0	0	Thermostat x has changed: The Thermostat setpoint/mode has been modified by the slave device (For example the Modbus thermostat connected to the Micro CAN has an updated value set by the user)
21	0	0	ID2	ID1	ID0	Data0	Data1	uCAN with ID2.ID1.ID0 reports an event with content Data0 and Data1, see Note3.
22	0	BA DeviceNr.MSB	BA DeviceNr.LSB	BA Type	BA Action	BA Extra Parameter.MSB	BA Extra Parameter.LSB	When BB debug mode is ON (see Eeprom Memory model Page 0 Byte 13), this Event will be send to the BB for every BA that has been executed.
249	0	x.MSB	x.LSB	y.MSB	y.LSB	0	z	This event will be send when BA251 is triggered. x, y and z are the parameters received from BA251.
250	0	0	Button_nr	Status	0	0	0	Front Panel Button change: The Frontpanel of the Core has 3 buttons, the Core+ has 4 buttons. When a Button is pressed (short press, longer press), an event will be send. Button_nr: 0->Setup Button, 1->Action Button, 2->CAN Power Button, 3->Select Button. Status: 0->Button released, 1->Button pressed, 2->Button pressed for 5 seconds, 3->Button pressed longer then 8 seconds.
251	Chip_Nr	Led_Blinking_25.MSB	Led_Blinking_25.LSB	Led_Blinking_50.MSB	Led_Blinking_50.LSB	Led_Blinking_75.MSB	Led_Blinking_75.LSB	Front Panel Led state change: When a Led of the Front Panel changes state (from ON to OFF or the reverse), an event message will be send. 2 led driver chips (Chip_nr 0 and 1) are present on the Front panel. The 16 bit Led_blinking_25 will indicate for the 16 leds if the led is blinking at 25% (BIT=1) or not (BIT=0), Led_blinking_50 for 50% and Led_blinking_75 for 75% ON (and thus 25% of the time OFF). See Note 2
252	Chip_Nr	0	0	Led_status.MSB	Led_status.LSB	0	0	Front Panel Led state change: When a Led of the Front Panel changes state (from ON to OFF or the reverse), an event message will be send. 2 led driver chips (Chip_nr 0 and 1) are present on the Front panel. The 16 bit Led_status will indicate for 16 leds if the led is ON (BIT=1) or OFF (BIT=0). See Note 2.
253	0	0	Bus	Power_state	0	0	0	Power state change: When Bus=0 -> RS485 Bus, When Bus=1 -> CAN Bus, when Power_state=0 -> Bus OFF, when Power_state=1 -> Bus ON
254	0	0	0	0	0	0	0	Eeprom activate has just been fully performed and is finished.
254	1	0	0	Onboard_temp	0	0	0	Update of the Onboard Main PCB temperature. Temperature is represented as a signed integer.
254	3	0	0	type	current health	previous health	0	This event indicates the health status: Type=0->CAN Health status change Current&previous health: Health=0: Value at startup Health=1: All uCAN's are not responding Health=2: All uCAN's OK Health=3: Not all uCAN's are responding
255	type	0	0	cause	0	0	0	Reset Action: type=0->Processor reset (or power startup) has just been performed type=1->Health checker is requesting reset in a few seconds cause=1->I2C Bus 1 (Eeprom) problem cause=2->I2C Bus 2 (Fram, front panel leds, Front panel DA, RTC etc) problem cause=3->CAN problem

Notes:

• Note 1: timer type specifies which kind of timer is active for a given output and his timer value.
  • timer type=0: No timer is active
  • timer type=1: 100ms timer
  • timer type=2: 1s timer
  • timer type=3: 1m timer
• Note 2:

Front Panel Led Events

Core	Core+	Description
NA	Chip 0 / Led 1	EXP BUS (0)
Chip 0 / Led 5	Chip 0 / Led 3	LED ST GREEN (1)
Chip 0 / Led 4	Chip 0 / Led 2	LED ST RED (2)
Chip 1 / Led 4	Chip 0 / Led 12	LED CAN ST GREEN (3)
Chip 1 / Led 5	Chip 0 / Led 11	LED CAN ST RED (4)
Chip 1 / Led 15	Chip 0 / Led 10	LED CAN COM (5)
Chip 1 / Led 13	Chip 0 / Led 9	LED P1 (6)
Chip 1 / Led 12	Chip 0 / Led 8	LED LAN GREEN (7)
Chip 1 / Led 11	Chip 0 / Led 5	LED LAN RED (8)
Chip 0 / Led 14	Chip 0 / Led 6	LED CLOUD (9)
Chip 0 / Led 13	Chip 0 / Led 7	LED SETUP (10)
NA	Chip 1 / Led 6	LED RELAY 1-8 (11)
NA	Chip 0 / Led 15	LED RELAY 9-16 (12)
NA	Chip 1 / Led 7	LED DIG OUT 1-4 (13)
NA	Chip 0 / Led 13	LED DIG OUT 5-7 (14)
NA	Chip 0 / Led 14	LED DIG ANA 1-4 (15)
NA	Chip 0 / Led 0	LED INPUTS (16)

• Note3: See Micro CAN Events